RAM Mounts ball sizes B, C, D and E: heavy-duty vehicle mounting
Choose the right RAM ball size, arm length and base for rugged tablets, laptops and displays in off-road and service vehicles, with RAM's load table and part-number letters.
In this guide
Every RAM mount is a chain of three parts: a ball base on the vehicle, a double socket arm and a ball on the device holder. The RAM ball size (B, C, D or E) sets how much weight that chain carries, so get it right first for a rugged tablet, laptop or display in an off-road or service vehicle. For docks, power and locking, see our RAM Mounts guide for defence and security vehicles.
- A scale: weigh the device with its case, holder or dock and cables, then compare with RAM's table
- The rail diameter, post width or flat area where the mount goes
- The vehicle maker's instructions for that area
![]()
Choose the RAM ball size by weight
| Size | Ball diameter | Approx. max load* | RAM's typical use |
|---|---|---|---|
| A | 14.3 mm (0.56") | 0.5 lb (≈0.23 kg) | Ultra-light devices |
| B | 25.4 mm (1") | 2 lb (≈0.9 kg) | Phones, GPS units, small tablets |
| C | 38.1 mm (1.5") | 4 lb (≈1.8 kg) | Large tablets, rougher rides |
| D | 57.2 mm (2.25") | 6 lb (≈2.7 kg) | Rugged tablets, laptops, heavy equipment |
| E | 85.9 mm (3.38") | 15 lb (≈6.8 kg) | Large displays, demanding industrial use |
* RAM: "Approximate capacity for a standard ball with a mid-length arm." Shorter arms and steel-reinforced posts increase real-world capacity (RAM). The kg values are our conversions.
RAM lists lower loads for heavy-duty use, so leave a margin for rough roads. If the device is too heavy for a size, RAM recommends the next size up. For rugged tablets, RAM's knowledge base says: "For most mobile terminals and rugged tablets that require modular mounting, the D-Size ball is sufficient."
Video: RAM Mounts
Pick the shortest arm that reaches
RAM UK says the rubber ball greatly reduces the vibration that reaches your electronics; it doesn't remove it.
| Size | Short | Medium | Long |
|---|---|---|---|
| B | 61 mm RAM-B-201U-A |
95 mm RAM-B-201U |
152 mm RAM-B-201U-C |
| C | 90 mm RAM-201U-B |
145 mm RAM-201U |
232 mm RAM-201U-D |
| D | 130 mm RAM-D-201U-C |
214 mm RAM-D-201U |
330 mm RAM-D-201U-E |
| E | 186 mm RAM-E-201U-D |
321 mm RAM-E-201U |
– |
Overall arm lengths, converted from RAM's inch figures. As RAM's footnote says, shorter arms increase real-world capacity. A longer arm is a longer lever: weight and bumps twist the ball joints harder, and the device swings further. Use the shortest arm that gives the reach you need.
- D-size short arm: the most margin for a heavy tablet.
- D-size medium arm: more reach when the base can't sit closer.
- RAM-D-254U round AMPS plate: a D ball for any holder or dock with the AMPS pattern.
- Hi-Torq wrench: extra grip on the knob of these D arms (step 4).
SCANSHOP is an official RAM Mounts reseller.
Recommended D-size RAM arms, ball plate and wrench
Buying for a fleet or a tender? Ask us for a quote.
Get a quoteHow to read RAM part numbers
RAM's naming guide puts the ball size after "RAM-": RAM-B- is B size, RAM- with no letter is C size, RAM-D- is D size and RAM-E- is E size. In RAM's examples the rest stays the same across sizes: 201U is the double socket arm, 202U the round plate. RAM doesn't explain the letter endings, which differ by size: compare the short arms above. For RAP- numbers, such as the C-size RAP-404U Tough-Claw, check the size in the product title.
Mixing ball sizes: change the ball, not the arm
An arm grips balls of its own size only; RAM says a D ball "is compatible with any other RAM® D Size ball & socket components". To combine sizes, change the ball:
- Holders and docks with the 4-hole AMPS pattern (≈30 × 38 mm): fit a B (RAM-B-347U), C (RAM-347U) or D (RAM-D-254U) ball plate. The GDS Tough-Dock for the Galaxy Tab Active5 uses this pattern.
- A second, light device on a C arm: the RAM-B-273-CU Add-A-Ball replaces the arm's bolt with a B ball; short and medium C arms only.
Choose the base for the mounting surface
Tough-Claw clamps need no tools but take only a B or C ball; for D-size loads use a metal D base.
| Surface | Base | Fit (RAM) |
|---|---|---|
| Flat panel or floor | RAM-D-202U round plate | ≈93 mm (3.68") drill-down plate |
| AMPS holder or flat surface | RAM-D-254U round AMPS plate | ≈64 mm (2.5"), 4-hole AMPS |
| VESA display or dock | RAM-D-246U-IN1 steel-reinforced plate | 100 × 100 and 75 × 75 mm holes |
| Rails and roll bars, no tools | Tough-Claw small, medium (RAP-404U) or large | Round ≈16–38, 25–48 or 25–57 mm; flat up to ≈29, 41 or 56 mm |
| Rails, D size | RAM-D-235U U-bolt base or RAM-D-271U-12 rail clamp | ≈25–32 mm (1"–1.25") or ≈32–48 mm (1.25"–1.875") |
| Square posts | RAM-D-247U-4 post clamp | Up to ≈102 mm (4") wide; RAM: "ideal for forklift mounting" |
| Lift-truck overhead guard | RAM-335 guard base | Steel plates with many hole patterns; up to two balls |
RAM: "Do not install this product near or over an airbag deployment area or in a location that obstructs the driver's vision or interferes with vehicle operation." Follow the vehicle maker's and RAM's instructions, check behind panels before drilling, and leave hardwired power to a qualified installer.
- Square post clamp base: a D ball on square posts, such as forklift posts.
- Tough-Claw medium: a tool-less C ball on rails and roll bars.
Recommended RAM bases for posts and rails
Buying for a fleet or a tender? Ask us for a quote.
Get a quoteTighten D-size arms with the Hi-Torq wrench
The Hi-Torq wrench fits the knob of D-size arms for an extra tight grip. RAM says it was originally made for the military, for cold weather when the knob could not be tightened by hand. Tighten by hand first; use the wrench only if a correctly sized set-up still moves when pushed firmly, and recheck after the first rough drives. To stop others removing the mount, RAM's Pin-Lock nut replaces the knob on D and E arms; see locking RAM mounts against theft.
Common mistakes
- An under-sized ball. Choose by total weight, not screen size.
- A long arm on a heavy device. It shakes on the road; move the base closer instead.
- Cranking the knob. If the device only holds with the knob as tight as you can get it, the ball is too small or the arm too long. No pliers or bars on knobs.
- Airbag zone or driver's view. Plan the position before you drill.
Frequently asked questions
What size RAM ball do I need for a 10-inch rugged tablet?
Weigh it with its case and holder or dock. RAM says D size is sufficient for most rugged tablets, and with a short arm it gives the most margin on rough roads. See our rugged tablet vehicle mount guide.
What is the difference between RAM B and C size?
The B ball is 25.4 mm (1") and the C ball 38.1 mm (1.5"). RAM's approximate maximum loads are 2 lb (≈0.9 kg) and 4 lb (≈1.8 kg), for a standard ball with a mid-length arm.
Are RAM B, C and D parts interchangeable?
No, an arm grips balls of its own size only. Combine sizes by changing the ball plate on the holder, for example to a D-size AMPS ball plate.
Do I need the Hi-Torq wrench?
Only if you can't tighten a D-size knob enough by hand, for example in cold weather.
Used in this guide
Compatible consumables and accessories for the RAM Mounts Double Socket Arm, D-Size, Medium Arm (RAM-D-201U).
Products used in this guide
| Product | Price | ||
|---|---|---|---|
![]() |
RAM Mounts Double Socket Arm, D-Size, Short ArmRAM-D-201U-C | 80,09 €+VATIn stock | |
![]() |
RAM Mounts Double Socket Arm, D-Size, Medium ArmRAM-D-201U | 124,64 €+VATOut of stock | View |
![]() |
RAM Mounts Round AMPS Plate with Ball, D-SizeRAM-D-254U | 40,76 €+VATIn stock | |
![]() |
RAM Mounts Hi-Torq Wrench for D-Size Socket ArmsRAM-KNOB9HU | 40,76 €+VATIn stock | |
![]() |
RAM Mounts Square Post Clamp Base for Posts up to 102 mm (4") Wide, D-SizeRAM-D-247U-4 | 82,70 €+VATIn stock | |
![]() |
RAM Mounts Tough-Claw Medium Clamp Ball Base for 25.4–40.6 mm Bars, C-SizeRAP-404U | 68,48 €+VATIn stock |
Related guides
Send us your model and a short description of the problem. Our team will help you find a solution.





