Ground support equipment tablet mounts: RAM for tugs and forklifts
Choose and fit RAM Mounts docks, holders and bases for Zebra handhelds, scanner guns and rugged tablets on airport tugs, baggage tractors, belt loaders, de-icing trucks and cargo forklifts.
In this guide
A ground support equipment tablet mount must cope with vibration, rain, frost, gloved hands and open cabs, and still keep the device charged and in place. This guide covers RAM Mounts docks, holders and bases for Zebra handhelds, scanner guns and rugged tablets on airport tugs, baggage tractors, belt loaders, de-icing trucks and cargo forklifts.
SCANSHOP is an official RAM Mounts reseller. For tablets in the cockpit, see our RAM aviation EFB tablet mounts guide.
![]()
Before you start
- The device model and its boot, frame or IntelliSkin sleeve
- The cab type (open or closed) and a solid mounting point
- The voltage of the vehicle's accessory supply
- Your needs for charging, USB and locking
Map the vehicle: cab, mounting point and view
Find a spot the operator can reach and read easily. In open cabs, as on many baggage tractors and forklifts, the device takes rain, cold and every bump: choose a dock that holds it firmly and locks. Keep the view ahead and to the load, the controls and the steps clear.
RAM: "Do not install this product near or over an airbag deployment area or in a location that obstructs the driver's vision or interferes with vehicle operation." Follow the vehicle maker's and RAM's instructions.
Choose the Zebra handheld and scanner vehicle mount
Zebra lists "Airlines (under wing)" among the TC73/TC78's markets; both are rated IP65 and IP68 with battery and take "bare or gloved fingertip input". RAM's matching docks and holders:
| Device | RAM product | Power | Lock |
|---|---|---|---|
| TC73, TC78 in IntelliSkin Next Gen | GDS Locking Dock, heated pins | USB-C | Key |
| TC22, TC27, TC53, TC58 in IntelliSkin | GDS Locking Dock for TC2x/TC5x | USB-C | Key |
| MC9300, MC9400 | Locking Powered Dock, heated pins | 5.5 mm DC | Key |
| MC9400 and other scanner guns | Power-Grip XL holder | None | None |
The GDS docks work one-handed and leave the buttons and scanner usable. On the heated-pin docks, RAM says heating elements "prevent pogo pins from locking up" in "wet and freezing environments" (no temperature given). The Power-Grip XL is, per RAM, compatible "with a full range of ball and socket forklift mounting systems".
RAM: "GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts." On open tugs, use the form-fit docks above.

Video: RAM Mounts
Choose the ground support equipment tablet mount
For an 8" Zebra ET4x or ET401, our first choice as a tug or forklift tablet mount is the Locking Tough-Dock. RAM states it is "MIL-STD 810G Shock and Vibration tested" (for this dock only). It has a key lock, a 5.5 mm DC input and two USB-A ports for peripherals, and fits C- and D-size bases. It takes the ET4x 8" in its Rugged Frame or the ET401 8" in a RAM Skin, not IntelliSkin. Zebra says the ET401 touchscreen works with gloved fingers "even in heavy rain" (ET401 setup guide). For other tablets, see rugged tablet vehicle mounts.

Video: RAM Mounts
Recommended RAM docks and holders for ground support equipment
Buying for a fleet or a tender? Ask us for a quote.
Get a quote- Locking Tough-Dock for ET4x 8": shock- and vibration-tested per RAM, locking, powered.
- GDS Locking Dock for TC73/TC78: heated pins, key lock; needs IntelliSkin Next Gen.
- Power-Grip XL: for scanner guns such as the MC9400.
Plan charging for cold and wet shifts
Match the charger to the dock and the vehicle:
- USB-C GDS docks: the 10–30 V GDS hardwire charger supplies USB-C Power Delivery (5–15 V, 3 A max); for 30–64 V supplies, use the 30–64 V version.
- 5.5 mm DC docks (ET4x Tough-Dock, MC9400 dock): RAM's DC-plug chargers differ in output voltage. Send us the dock's part number and we'll check which charger RAM lists for it.
RAM's compatibility guide: fuel-powered trucks and propane forklifts typically work with ~10–32 V chargers; electric forklifts require a higher input range, ~24–64 V. For electric tugs, check the accessory voltage in the vehicle documentation. More in our GDS hardwire charger guide.
RAM rates the USB-C GDS chargers for −20 °C to +70 °C, but Zebra's charging ranges are narrower: 5–40 °C for the TC22/TC27, 0–40 °C for the ET401. A frozen device may not charge, and RAM doesn't say heated pins warm it. In winter, prefer heated cabs and swap batteries indoors (TC73/TC78: Warm or Hot Swap, per Zebra).
Pick the base: roll bar, post or overhead guard
| Mounting point | RAM base | Notes |
|---|---|---|
| Roll bar or rail: round, square or odd-shaped | Tough-Claw Medium, C | Tool-less; 1"–1.875" (≈25–48 mm) round, up to 1.6" (≈41 mm) flat |
| Square post up to 4" (≈102 mm) | Square Post Clamp Base, D | RAM: "ideal for forklift mounting" |
| Overhead guard or lift cage | Lift Truck Overhead Guard Base | Steel plates that carry C or D ball bases; no load figure published |
| Dashboard in a closed cab | Round plate with ball, D | Drill-down |
| Crown truck with a Crown Work Assist clamp | Crown Work Assist ball base, D | Only for Crown Work Assist clamp accessories; clamp not included |
We use C size for handheld docks, D for tablet docks and scanner holders. RAM's approximate maximum load is 4 lb (≈1.8 kg) for C and 6 lb (≈2.7 kg) for D: "Approximate capacity for a standard ball with a mid-length arm. Shorter arms and steel-reinforced posts increase real-world capacity." Use the shortest arm that reaches, such as the D-size short arm (≈130 mm); see our RAM ball sizes guide.
Typical builds: handheld dock + C diamond ball base + C arm + Tough-Claw; tablet dock or Power-Grip XL + D round AMPS plate + D arm + post clamp or guard plates.
Recommended RAM bases and charging for tugs and forklifts
Buying for a fleet or a tender? Ask us for a quote.
Get a quoteInstall, lock and check the mount
- Check the position with the operator seated: view, controls, steps and airbag labels.
- Fit the base as RAM's instructions describe. On a forklift, follow the truck maker's rules for the overhead guard.
- Have a qualified installer hardwire the charger, fused per the vehicle maker's and RAM's instructions (RAM gives no fuse rating for the USB-C chargers), on a battery feed (always on) or the cab fuse block (on ignition).
- Route cables clear of moving parts, hot surfaces and sharp edges.
- Lock the dock, and fit a Pin-Lock security nut to D-size arms; see our RAM locking guide.
- Test docking with gloves on, and check the knobs again after the first shifts.
Equipping a fleet? Send us the devices, vehicle types and voltages, and we'll prepare a RAM parts list and quote.
Frequently asked questions
What is the best airport tug tablet mount for an open cab?
A key-locking form-fit dock, such as the Locking Tough-Dock for the Zebra ET4x 8", on a short D-size arm and a post clamp or overhead-guard base. RAM does not recommend GDS Uni-Conn snap-in docks for open cockpits.
How do I mount a Zebra MC9400 scanner on a forklift?
Put the Power-Grip XL holder (RAP-450U) on a D-size round AMPS plate, arm and a square post clamp or overhead guard base. RAM also makes locking MC9400 docks.
Will a Zebra handheld charge in a vehicle dock below freezing?
Often not. RAM's USB-C GDS chargers are rated down to −20 °C, but Zebra's charging ranges start at 0 °C or 5 °C, depending on the model.
Does the RAM Crown ball base fit any forklift?
No. RAM-D-202U-CRO1 fits Crown Work Assist clamp accessories only, and the clamp is not included.
Used in this guide
Compatible consumables and accessories for the Zebra ET40.
Products used in this guide
| Product | Price | ||
|---|---|---|---|
![]() |
RAM Mounts Locking Tough-Dock with Power + Dual USB for Zebra ET4x 8" with Rugged FrameRAM-HOL-ZE20PD2KLU | 351,66 €+VATIn stock | |
![]() |
RAM Mounts GDS Locking Powered Dock with USB-A and Heated Pins for Zebra TC73/TC78RAM-GDS-DOCKL-V12-ZE35CPDHU | 391,00 €+VATIn stock | |
![]() |
RAM Mounts Power-Grip XL Universal Scanner Gun HolderRAP-450U | 64,22 €+VATOut of stock | View |
![]() |
RAM Mounts Tough-Claw Medium Clamp Ball Base for 25.4–40.6 mm Bars, C-SizeRAP-404U | 68,48 €+VATIn stock | |
![]() |
RAM Mounts Square Post Clamp Base for Posts up to 102 mm (4") Wide, D-SizeRAM-D-247U-4 | 82,70 €+VATIn stock | |
![]() |
RAM Mounts GDS Modular USB-C Power Delivery Hardwire Charger 45 W, 10–30 V InRAM-GDS-CHARGE-V3C-3U | 148,10 €+VATIn stock |
More Zebra ET40 guides
Send us your model and a short description of the problem. Our team will help you find a solution.





